Linux version 2.6.23-rc1-mm1 (root@debian32) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 Sun Jul 29 21:46:47 PDT 2007
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 00000000077f0000 (usable)
 BIOS-e820: 00000000077f0000 - 00000000077f3000 (ACPI NVS)
 BIOS-e820: 00000000077f3000 - 0000000007800000 (ACPI data)
 BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
119MB LOWMEM available.
Entering add_active_range(0, 0, 30704) 0 entries of 256 used
sizeof(struct page) = 32
Zone PFN ranges:
  DMA             0 ->     4096
  Normal       4096 ->    30704
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0:        0 ->    30704
On node 0 totalpages: 30704
Node 0 memmap at 0xc1000000 size 983040 first pfn 0xc1000000
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 4064 pages, LIFO batch:0
  Normal zone: 207 pages used for memmap
  Normal zone: 26401 pages, LIFO batch:7
  Movable zone: 0 pages used for memmap
DMI 2.2 present.
ACPI: RSDP 000F67C0, 0014 (r0 VIA601)
ACPI: RSDT 077F3000, 0028 (r1 VIA601 AWRDACPI 42302E31 AWRD        0)
ACPI: FACP 077F3040, 0074 (r1 VIA601 AWRDACPI 42302E31 AWRD        0)
ACPI: DSDT 077F30C0, 29BC (r1 VIA601 AWRDACPI     1000 MSFT  100000C)
ACPI: FACS 077F0000, 0040
ACPI: PM-Timer IO Port: 0x4008
Allocating PCI resources starting at 10000000 (gap: 07800000:f87f0000)
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 30465
Kernel command line: root=/dev/hda1 ro netconsole=4444@10.1.10.1/eth1,6666@10.1.10.43/00:0E:7B:1A:C8:74
netconsole: local port 4444
netconsole: local IP 10.1.10.1
netconsole: interface eth1
netconsole: remote port 6666
netconsole: remote IP 10.1.10.43
netconsole: remote ethernet address 00:0e:7b:1a:c8:74
Initializing CPU#0
PID hash table entries: 512 (order: 9, 2048 bytes)
Detected 533.387 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
... MAX_LOCKDEP_SUBCLASSES:    8
... MAX_LOCK_DEPTH:          30
... MAX_LOCKDEP_KEYS:        2048
... CLASSHASH_SIZE:           1024
... MAX_LOCKDEP_ENTRIES:     8192
... MAX_LOCKDEP_CHAINS:      16384
... CHAINHASH_SIZE:          8192
 memory used by lock dependency info: 992 kB
 per task-struct memory footprint: 1200 bytes
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 115856k/122816k available (1942k kernel code, 6432k reserved, 696k data, 184k init, 0k highmem)
virtual kernel memory layout:
    fixmap  : 0xffff6000 - 0xfffff000   (  36 kB)
    vmalloc : 0xc8000000 - 0xffff4000   ( 895 MB)
    lowmem  : 0xc0000000 - 0xc77f0000   ( 119 MB)
      .init : 0xc0396000 - 0xc03c4000   ( 184 kB)
      .data : 0xc02e590a - 0xc0393b44   ( 696 kB)
      .text : 0xc0100000 - 0xc02e590a   (1942 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
SLUB: Genslabs=22, HWalign=32, Order=0-3, MinObjects=16, CPUs=1, Nodes=1
Calibrating delay using timer specific routine.. 1068.49 BogoMIPS (lpj=1779984)
kswapd reclaim order set to 3
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 00803035 80803035 00000000 00000000 00000000 00000000 00000000 00000000
CPU: L1 I Cache: 64K (32 bytes/line), D cache 64K (32 bytes/line)
CPU: L2 Cache: 64K (32 bytes/line)
CPU: After all inits, caps: 00803135 80803035 00000000 00000000 00000000 00000000 00000000 00000000
Compat vDSO mapped to ffffe000.
CPU: Centaur VIA Samuel 2 stepping 03
Checking 'hlt' instruction... OK.
ACPI: Core revision 20070126
ACPI: setting ELCR to 0008 (from 1c28)
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfb3a0, last bus=1
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 11 *12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 *5 6 7 10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 10 devices
ACPI: ACPI bus type pnp unregistered
Generic PHY: Registered new driver
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
Time: tsc clocksource has been installed.
pnp: 00:00: iomem range 0xcc000-0xcffff has been reserved
pnp: 00:00: iomem range 0xda000-0xdbfff has been reserved
pnp: 00:00: iomem range 0xf0000-0xfbfff could not be reserved
pnp: 00:00: iomem range 0xfc000-0xfffff could not be reserved
PCI: Bridge: 0000:00:01.0
  IO window: disabled.
  MEM window: e0000000-e2ffffff
  PREFETCH window: 10000000-100fffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 5, 131072 bytes)
TCP bind hash table entries: 4096 (order: 5, 131072 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
Unpacking initramfs...<6>Switched to high resolution mode on CPU 0
 done
Freeing initrd memory: 1477k freed
io scheduler noop registered
io scheduler cfq registered (default)
PCI: VIA PCI bridge detected. Disabling DAC.
PCI: Firmware left 0000:00:14.0 e100 interrupts enabled, disabling
Boot video device is 0000:01:00.0
ACPI Exception (processor_throttling-0084): AE_NOT_FOUND, Evaluating _PTC [20070126]
ACPI Exception (processor_throttling-0147): AE_NOT_FOUND, Evaluating _TSS [20070126]
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [CPU0] (supports 2 throttling states)
Serial: 8250/16550 driver $Revision: 1.90 $ 1 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
parport_pc: VIA 686A/8231 detected
parport_pc: probing current configuration
parport_pc: Current parallel port base: 0x378
parport0: PC-style at 0x378, irq 7 [PCSPP,EPP]
parport0 (IRQ 7) handled a spurious interrupt
parport_pc: VIA parallel port: io=0x378, irq=7
e100: Intel(R) PRO/100 Network Driver, 3.5.23-k4-NAPI
e100: Copyright(c) 1999-2006 Intel Corporation
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:14.0[A] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
e100: eth0: e100_probe: addr 0xe4101000, irq 11, MAC addr 00:A0:C9:99:E1:75
via-rhine: Broken BIOS detected, avoid_D3 enabled.
via-rhine.c:v1.10-LK1.4.3 2007-03-06 Written by Donald Becker
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:12.0[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10
eth1: VIA Rhine II at 0xe4100000, 00:40:63:d3:1e:97, IRQ 10.
eth1: MII PHY found at address 1, status 0x7869 advertising 05e1 Link c5e1.
Davicom DM9161E: Registered new driver
Davicom DM9161A: Registered new driver
Davicom DM9131: Registered new driver
Cicada Cis8204: Registered new driver
Cicada Cis8201: Registered new driver
LXT970: Registered new driver
LXT971: Registered new driver
QS6612: Registered new driver
SMSC LAN83C185: Registered new driver
Vitesse VSC8244: Registered new driver
netconsole: device eth1 not up yet, forcing it
eth1: link up, 100Mbps, full-duplex, lpa 0xC5E1
netconsole: carrier detect appears untrustworthy, waiting 4 seconds
console [netcon0] enabled
netconsole: network logging started
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:11.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8231 (rev 10) IDE UDMA100 controller on pci0000:00:11.1
    ide0: BM-DMA at 0xd000-0xd007, BIOS settings: hda:pio, hdb:pio
    ide1: BM-DMA at 0xd008-0xd00f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
hda: PQI IDE DiskOnModule, ATA DISK drive
hda: host max PIO5 wanted PIO255(auto-tune) selected PIO2
hda: set_drive_speed_status: status=0x51 { DriveReady SeekComplete Error }
hda: set_drive_speed_status: error=0x04 { DriveStatusError }
hda: host max PIO5 wanted PIO255(auto-tune) selected PIO2
hda: set_drive_speed_status: status=0x51 { DriveReady SeekComplete Error }
hda: set_drive_speed_status: error=0x04 { DriveStatusError }
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hda: max request size: 128KiB
hda: 256000 sectors (131 MB) w/1KiB Cache, CHS=500/16/32
 hda: hda1
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:00:11.2[D] -> Link [LNKD] -> GSI 5 (level, low) -> IRQ 5
uhci_hcd 0000:00:11.2: UHCI Host Controller
uhci_hcd 0000:00:11.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:11.2: irq 5, io base 0x0000d400
usb usb1: new device found, idVendor=0000, idProduct=0000
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: UHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.23-rc1-mm1 uhci_hcd
usb usb1: SerialNumber: 0000:00:11.2
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:11.3[D] -> Link [LNKD] -> GSI 5 (level, low) -> IRQ 5
uhci_hcd 0000:00:11.3: UHCI Host Controller
uhci_hcd 0000:00:11.3: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:11.3: irq 5, io base 0x0000d800
usb usb2: new device found, idVendor=0000, idProduct=0000
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.23-rc1-mm1 uhci_hcd
usb usb2: SerialNumber: 0000:00:11.3
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
cpuidle: using governor menu
GACT probability NOT on
Mirror/redirect action on
u32 classifier
    Performance counters on
    input device check on 
    Actions configured 
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
ctnetlink v0.93: registering with nfnetlink.
ip_tables: (C) 2000-2006 Netfilter Core Team
arp_tables: (C) 2002 David S. Miller
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
longhaul: VIA C3 'Samuel 2' [C5B] CPU detected.  Longhaul v1 supported.
longhaul: Using northbridge support.
Using IPI Shortcut mode
Freeing unused kernel memory: 184k freed
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
Marking TSC unstable due to: possible TSC halt in C2.
Time: acpi_pm clocksource has been installed.
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
Clocksource tsc unstable (delta = -118300091 ns)
process `syslogd' is using obsolete setsockopt SO_BSDCOMPAT